SJ5000+ Wlan Probleme - WIFI Direct

Wer immer wieder Probleme mit dem Wlan hat sollte mal den Direktmodus der Kamera probieren,
dazu müsst ihr die Config Datei der Cam bearbeiten, der Eintrag AP muss in P2P geändert werden, dann am Smartphone die Direktverbindung aktivieren , fertig.
Bei mir läuft es wesentlich stabiler

--------------------------------------
##### Wifi configuration file ##########################################
## Empty lines and lines starting with # are ignored
# ap: SoftAP mode
# sta: Station mode
# p2p: Enable Wifi Direct Support for peer-to-peer connectibity
WIFI_MODE=ap <<<<< hier p2p eintragen
# GPIO pin to enable or disable WiFi
#WIFI_EN_GPIO=95

##### STA mode configuration ##########################################
# SSID
ESSID=amba_boss
# Passphrase. Leave empty at no security mode; please edit wpa_supplicant.conf when your AP cannot be detected
PASSWORD=1234567890
# Device Name for AMBA Discovery Protocol (optional)
STA_DEVICE_NAME=amba-1

##### Wifi Direct configuration ##########################################
# Find devices with correct name prefix and automatically connect at startup
P2P_AUTO_CONNECT=no
# Auto-connect with devices if the name prefix matches
P2P_CONNECT_PREFIX=amba
## Do not enable this optional field unless you are certain
# please provide a unique name amoung multiple devices to prevent confusion
#P2P_DEVICE_NAME=amba-1
## Do not enable this optional field unless you are certain
# Set the default P2P GO Intent
#P2P_GO_INTENT=0
## Do not enable this optional field unless you are certain
# Specify P2P operating channel
#P2P_OPER_CHANNEL=1
## Do not enable this optional field unless you are certain
# Default mode for HT40 enable when operating as GO
#P2P_GO_HT40=0

##### SoftAP configuration ##########################################
# SSID (1 ~ 32 characters)
AP_SSID=SJ5000+
# IP address
LOCAL_IP=192.168.42.1
# IP subnet mask
LOCAL_NETMASK=255.255.255.0
# IP pool starting address of DHCP server
DHCP_IP_START=192.168.42.2
# IP pool end address of DHCP server
DHCP_IP_END=192.168.42.6
# Wifi channel number, set 0 to use Auto Channel Selection
AP_CHANNEL=0
# Maximum number of stations allowed in station table
AP_MAXSTA=5
# If you say yes here, all WPA/WEP settings will be ignored
AP_PUBLIC=no
# WPA Passphrase (8 ~ 63 characters)
AP_PASSWD=12345678

##### Advanced WPA configuration ##########################################
## Do not modify this section unless you are certain
# This is a bit field, bit0 = WPA, bit1 = WPA2
WPA_VERSION=2
# This is a space separated list of encryption algorithms, TKIP CCMP
WPA_PAIRWISE=CCMP

##### Advanced WEP configuration ##########################################
## Do not modify this section unless you are certain
# If you say yes here, AP_PASSWD, WPA_VERSION, WPA_PAIRWISE will be ignored
AP_WEP=no
# Bit fields of allowed authentication algorithms, bit 0 = Open System, bit 1 = Shared Key
AUTH_ALGS=1
# The key number to use when transmitting. It must be between 0 and 3, and the corresponding key must be set.
WEP_DEFAULT_KEY=0
# A key may be a quoted string (5 or 13 characters) or unquoted hexadecimal digits (10 or 26 digits), depending on whether 64-bit or 128-bit WEP is used
WEP_KEY0=1234567890
WEP_KEY1=”vwxyz”
WEP_KEY2=0102030405060708090a0b0c0d
WEP_KEY3=”.2.4.6.8.0.23″