So ein paar Infos zum Akku;
Aufnahme Auflösung 1920x1280, ohne Wifi, > 55 min
das Problem der fehlenden Pufferbatterie besteht weiterhin, also am besten rechtzeitig mit der Cam laden
Lässt man das USB Ladekabel dran, geht es auch ohne Neueinstellen
Was sind denn das für schwarze Ränder in den Ecken?
Ist Vignetting etwa wieder ein Thema??
ja, ist aber nicht bei allen Auflösungen, liegt aber an der starke gekrümmten Linse
Noch etwas negatives, bei eingeschalteten Wifi ist ein brummen bei der Aufnahme zu hören
auf der SD liegt eine Datei mit Namens wifi.conf, anscheinend eine Konfigurations-Datei, mal schauen wer was daraus herausfindet
Vermutlich lässt sich hier der Name der Cam und auch das Passwort ändern.
Station Mode könnte darauf hindeuten das man die Cam auch in ein bestehendes Netz einbinden könnte
p2p könnte auf eine peer to peer Verbindung hinweisen
bin gespannt wer sich alles was zutraut zu ändern :)
------------------------------------------------------------------------------------------------------------
##### Wifi configuration file ##########################################
## Empty lines and lines starting with # are ignored
# ap: SoftAP mode
# sta: Station mode
# p2p: Enable Wifi Direct Support for peer-to-peer connectibity
WIFI_MODE=ap
# GPIO pin to enable or disable WiFi
#WIFI_EN_GPIO=95
##### STA mode configuration ##########################################
# SSID
ESSID=amba_boss
# Passphrase. Leave empty at no security mode; please edit wpa_supplicant.conf when your AP cannot be detected
PASSWORD=1234567890
# Device Name for AMBA Discovery Protocol (optional)
STA_DEVICE_NAME=amba-1
##### Wifi Direct configuration ##########################################
# Find devices with correct name prefix and automatically connect at startup
P2P_AUTO_CONNECT=no
# Auto-connect with devices if the name prefix matches
P2P_CONNECT_PREFIX=amba
## Do not enable this optional field unless you are certain
# please provide a unique name amoung multiple devices to prevent confusion
#P2P_DEVICE_NAME=amba-1
## Do not enable this optional field unless you are certain
# Set the default P2P GO Intent
#P2P_GO_INTENT=0
## Do not enable this optional field unless you are certain
# Specify P2P operating channel
#P2P_OPER_CHANNEL=1
## Do not enable this optional field unless you are certain
# Default mode for HT40 enable when operating as GO
#P2P_GO_HT40=0
##### SoftAP configuration ##########################################
# SSID (1 ~ 32 characters)
AP_SSID=SJ5000+
# IP address
LOCAL_IP=192.168.42.1
# IP subnet mask
LOCAL_NETMASK=255.255.255.0
# IP pool starting address of DHCP server
DHCP_IP_START=192.168.42.2
# IP pool end address of DHCP server
DHCP_IP_END=192.168.42.6
# Wifi channel number, set 0 to use Auto Channel Selection
AP_CHANNEL=0
# Maximum number of stations allowed in station table
AP_MAXSTA=5
# If you say yes here, all WPA/WEP settings will be ignored
AP_PUBLIC=no
# WPA Passphrase (8 ~ 63 characters)
AP_PASSWD=12345678
##### Advanced WPA configuration ##########################################
## Do not modify this section unless you are certain
# This is a bit field, bit0 = WPA, bit1 = WPA2
WPA_VERSION=2
# This is a space separated list of encryption algorithms, TKIP CCMP
WPA_PAIRWISE=CCMP
##### Advanced WEP configuration ##########################################
## Do not modify this section unless you are certain
# If you say yes here, AP_PASSWD, WPA_VERSION, WPA_PAIRWISE will be ignored
AP_WEP=no
# Bit fields of allowed authentication algorithms, bit 0 = Open System, bit 1 = Shared Key
AUTH_ALGS=1
# The key number to use when transmitting. It must be between 0 and 3, and the corresponding key must be set.
WEP_DEFAULT_KEY=0
# A key may be a quoted string (5 or 13 characters) or unquoted hexadecimal digits (10 or 26 digits), depending on whether 64-bit or 128-bit WEP is used
WEP_KEY0=1234567890
WEP_KEY1="vwxyz"
WEP_KEY2=0102030405060708090a0b0c0d
WEP_KEY3=".2.4.6.8.0.23"
So nun der 720p Low Light Test, jeweils kurze Sequenzen in 120fps,60fps und 30fps. Hier kann man sagen das bedingt durch die kurze Belichtung bei 120p dieser Modus bei Low Light unbrauchbar ist. Skifahrer sollten bei schlechten Wetter also umstellen auf mind. 60fps. Wie das ganze bei besten Wetter aussieht ist abzuwarten. Für scharfe Zeitlupen währen die 120fps schon super.
https://www.youtube.com/watch?v=UR_dQBdr4uc
Hab mal versucht das Menu zu entziffern und es in ein PDF grafisch dargestellt, wenn etwas nicht stimmen sollte, gebt Bescheid
Hi,
habe die sj4000 wifi gerade erst bekommen, sprich noch Widerrufsrecht. Hatte mir diese für das Walkera Gimbal gekauft.
Musste nun feststellen, dass auch der Nachfolger sj5000 wifi und sj5000 plus am Start ist.
In den diversen Vergleichsvideos zwischen den Beiden sieht man, dass die 5000er etwas breiter als die 4000er ist. Laut Datenblatt nur 1mm, es sieht aber nach mehr aus.
Die 4000er passt gerade so in die Gimbalhalterung, daher wäre es super, wenn du die exakten Daten Breite und Höhe feststellen und hier mitteilen könntest. Es geht um jeden Millimeter.
Danke
Andy
Danke für die Benüdarstellung, schaut echt gut aus TOP
In meinen Gimbal Feiyu Tech FY G3 passt die Sj5000 nicht mehr rein, leider